I am installing a remote start got it hooked up and it starts fine problem is it keep on trying to start again after its already started any help would be appreciated thankfulness!
It sounds to resembling you got it surrounded by tach mode and you do not have the tach mode flex hooked up properly to sense it is running. Set it up in non tach , sort sure all switches are contained by the proper position and see what happens.
These websites may comfort and have user forums too. If near is a reprogramming or initializing procedure, I would go through those steps from mark. It's like rebooting your PC to clear it's memory brains out. You could also try disconnecting your car's gloomy black battery cable, but that will also reset your radio and auto computer settings.
http://www.commandocaralarms.com/wirings...
http://www.the12volt.com/
Answers: Check your wiring, If the Alternator is not putting out 13 to 14 volts DC, as needed, the system will not denote an increase surrounded by voltage and regrind the starter.
To solve this, make sure the addition wire is connected properly surrounded by the Ignition Switch Harness.
What is the difference between Tach Mode and Tachless Mode on a Remote Starter?
The difference is the amount of crank time. In Tach Mode the crank time is approximately six seconds. In Tachless Mode the module will engross the starter up to four times at an interval of 0.5 seconds. Tachless Mode save you time during the installation due to the fact that you enjoy one less chain to locate and hook up.
Do I have to use the Tach chain when installing my Remote Starter?
“NO”. The Tach is provided in grip you have a rock-hard starting vehicle (this is if your vehicle takes more than six second of crank time to start) or if you live in an nouns of extreme temperatures. In any case the Tach flex provides extra crank time.
I don't know what vehicle you are installing this in but you enjoy to power up all ignition wires. If your vehicle is equipped beside an ignition 3 that needs to powered up as very well.
If you need any spare help contact me via my email, I used to install these for a living.
Where can I obtain an artistic vehicle...
It sounds to resembling you got it surrounded by tach mode and you do not have the tach mode flex hooked up properly to sense it is running. Set it up in non tach , sort sure all switches are contained by the proper position and see what happens.
When i cut on the warmth it...
These websites may comfort and have user forums too. If near is a reprogramming or initializing procedure, I would go through those steps from mark. It's like rebooting your PC to clear it's memory brains out. You could also try disconnecting your car's gloomy black battery cable, but that will also reset your radio and auto computer settings.
http://www.commandocaralarms.com/wirings...
http://www.the12volt.com/
Whats the best muffler for my LT1...
Answers: Check your wiring, If the Alternator is not putting out 13 to 14 volts DC, as needed, the system will not denote an increase surrounded by voltage and regrind the starter.
To solve this, make sure the addition wire is connected properly surrounded by the Ignition Switch Harness.
What is the difference between Tach Mode and Tachless Mode on a Remote Starter?
The difference is the amount of crank time. In Tach Mode the crank time is approximately six seconds. In Tachless Mode the module will engross the starter up to four times at an interval of 0.5 seconds. Tachless Mode save you time during the installation due to the fact that you enjoy one less chain to locate and hook up.
Do I have to use the Tach chain when installing my Remote Starter?
“NO”. The Tach is provided in grip you have a rock-hard starting vehicle (this is if your vehicle takes more than six second of crank time to start) or if you live in an nouns of extreme temperatures. In any case the Tach flex provides extra crank time.
I don't know what vehicle you are installing this in but you enjoy to power up all ignition wires. If your vehicle is equipped beside an ignition 3 that needs to powered up as very well.
If you need any spare help contact me via my email, I used to install these for a living.
Resolved Questions
- Is it ok to us Synthetic Oil...
- What should I do if the brakes...
- How can you fix a gas cistern...
- Have a 98 lincoln town saloon and...
- Port and polish happenstance?
- Is it the master cylinder?
- Infniti charging system issues?
- Installing 300ex pad?
- How long can I drive beside a...
- 99 Chevy Silverado "Wiper" problems ?